-
Auto Adapters — GE1950-1276
The Lind GE1950-1276 DC/DC Power Adapter is designed to power your Getac-compatible laptop computer and to charge its internal battery from an 11-16 VDC power source. The adapter supplies current and voltage levels as required by the laptop.
– Cig. Plug 36″ Input Cable
– Kycon 4 pin 36″ Output Cable
– Low Input Voltage Disconnect
– High Input Voltage Disconnect
– Output Short Circuit Protection
– Output Overcurrent Protection
– Internal Over Temperature Protection -
Auto Adapters — MS1555-5287
The Lind MS1555-5287 Auto Power Adapter is designed to power your Microsoft Surface Pro from a 11-16 VDC power source.
– 11-16 VDC
– 36″ Barewire
– 36″ MS Surface Pro Connector -
Auto Adapters — ZE1235I-4424
The Lind ZE1235I-4424 DC/DC Power Adapter is designed to power your Zebra Tablet Device from a 20-60 VDC power source.
– 20-60 VDC
– Bare Wire 72″ Input Cable
– 2.1mm Snap-In 72″ Output cable -
Isolated Adapters — GE1950I-4315
The Lind GE1950I-4315 DC/DC Power Adapter is designed to power your Getac-compatible laptop computer and to charge its internal battery from an 12-32 VDC power source. The adapter supplies current and voltage levels as required by the laptop.
– Isolated
– Bare Wire 72″ Input Cable
– Kycon 4 pin 36″ Output Cable
– 5.5×2.5 36″ Output Cable
– Low Input Voltage Disconnect
– High Input Voltage Disconnect
– Output Short Circuit Protection
– Output Overcurrent Protection
– Internal Over Temperature Protection -
Isolated Adapters —DT19-12I-4382
The Lind DT19-12I-4382 DC/DC Power Adapter is designed to power your DT Research & Zebra Printer and to charge its internal battery from a 20-60 VDC power source.
– Isolated
– 20-60 VDC
– Bare Wire 72″ Input Cable -
Isolated Adapters —DT1935I-3980
The Lind DT1935I DC/DC Power Adapter is designed to power your DT Research 390 and to charge its internal battery from an 12-32 VDC power source.
– Isolated
– 12-32 VDC
– Bare Wire 72″ Input Cable
– 4.75×1.7 72″ Output Cable -
Shutdown Timer — LPT1230-052
The Lind LPT1230-052 Low Profile Shutdown Timer protects your vehicle’s battery from over-discharge and equipment from low voltage and high voltage damage. This device turns off electrical loads at a preset time after the car engine is shut down. This timer provides the same protective functions as Lind’s standard Shutdown Timers but comes with a reduced height profile for installation into more compact areas.
– 11-16 VDC
– More compact design via reduced height profile
– Adjustable shut down delay time (from 5 seconds to 4 hours, factory set to 2 hours)
– Low voltage shut down at 10.5 Vdc
– High voltage shut down at 18 Vdc with auto reset
– Loads up to 30 amps -
Shutdown Timer — LPT1230-072
The Lind LPT1230-072 DC/DC Power Adapter is designed to power your Low Profile Timer from an 11-16 VDC power source.
– 11-16 VDC
-
Shutdown Timer — SDT1220-046
The Lind SDT1220-046 Shutdown Timer is designed to protect your vehicle’s battery from over discharge. This Lind Ruggedized Shutdown Timer/Relay Driver turns off electrical loads after the vehicle’s ignition is shut off. Used as a Shutdown Timer, this unit alone can be used with loads up to 20A. As a Relay Driver/Shutdown Timer, it will drive relays up to 200 amps.
– 11-16 VDC
– Epoxy sealed electronics for under-the-hood installation
– Factory programmed – 10 Min. to 2 Hr. Delayed Shut Off
– Automatic low voltage shut off
– No adjustments and installation is easy
– Will drive 40, 80 150, 200 Amp external relays
